Close-up of electronic control circuitry and microchips on a dark circuit board
Battery Technology

Extreme-temperature LiFePO4 with integrated battery management

Batteries built with low-temperature lithium iron phosphate cells and a built-in BMS, supplied to commercial buyers with documentation for the exact model.

Current models

Both current batteries use the same low-temperature LiFePO4 cells and operate without an internal heater.

Current model

WT-LFP12-100 · 12V 100Ah

A 12-volt lithium iron phosphate battery for solar-charged, remote and outdoor equipment.

Electrical and mechanical values come from the manufacturer's current specification sheet for this model. Temperature, cycle-life and documentation details are confirmed by the manufacturer.

Request the specification sheet

ModelWT-LFP12-100
ChemistryLithium iron phosphate (LiFePO4)
Nominal voltage12.8 V
Rated capacity100 Ah (10-hour rate)
Energy1,280 Wh
Max. charging current100 A
Max. continuous discharge current100 A
Battery managementIntegrated BMS
Internal heaterNone (heater-free)
Cell temperature (manufacturer-confirmed)Charge to −35°C (−31°F), discharge to −40°C (−40°F)
Cycle life4,000+ cycles with 80% capacity remaining
Series / parallelUp to 4 in series, up to 16 in parallel
DocumentationMSDS, UN38.3, IP67 (manufacturer-confirmed; coverage for this model confirmed on request)
TerminalsScrew terminal
Case materialABS + PC
Dimensions (L × W × H)10.25 × 6.7 × 8.4 in
WeightApprox. 22 lb
Current model

24V 100Ah

A 24-volt lithium iron phosphate battery for 24V systems and OEM equipment.

This is the current 24V configuration. Charge and discharge current limits are set in the BMS firmware and configured for each customer's approved application, so current ratings are confirmed with your quote.

Request 24V pricing

Configuration24V 100Ah
ChemistryLithium iron phosphate (LiFePO4)
Voltage24 V
Capacity100 Ah
Battery managementIntegrated BMS; charge and discharge limits configurable in firmware
Internal heaterNone (heater-free)
Cell temperature (manufacturer-confirmed)Charge to −35°C (−31°F), discharge to −40°C (−40°F)
Cycle life4,000+ cycles with 80% capacity remaining
Series / parallelUp to 4 in series, up to 16 in parallel
DocumentationUL1642 (lithium cell standard); MSDS, UN38.3, IP67 (manufacturer-confirmed; coverage for this configuration confirmed on request)
Dimensions and weightProvided with the specification for your configuration
Heater-free extreme-temperature LiFePO4 technology

Designed for cold-weather operation

Standard LiFePO4 batteries are commonly restricted from charging below freezing. For unattended equipment in cold climates, that can mean lost charging days and lost uptime.

Both the 12V and 24V batteries use the same low-temperature LiFePO4 cells. The manufacturer rates these cells for charging down to −35°C (−31°F) and discharging down to −40°C (−40°F), and confirms that the batteries do not require heating in low-temperature conditions. They operate within their suitable temperature range with no internal heater.

These are cell ratings. Complete-battery operating limits, charging-current curves and application conditions depend on the BMS settings, charge rate, load and installation, and the manufacturer provides them for your project. We review your site conditions before recommending a configuration.

Battery management system

Every battery includes an integrated battery management system that manages charging and discharging and protects the cells.

  • Monitoring software: the manufacturer's software connects through the battery's RJ45 port and displays a wide range of operating parameters. Tell us what your equipment needs to monitor, and we confirm the details for your model.
  • Configurable current limits: charge and discharge limits are set in the BMS firmware and adjusted by the manufacturer to match your approved requirements.
  • Series and parallel: up to 4 batteries in series and up to 16 in parallel.

Cycle life and capacity retention

The manufacturer confirms 4,000+ charge and discharge cycles with 80% of capacity remaining. Actual service life depends on depth of discharge, temperature, charge rate and load.

Certifications and technical documentation

The manufacturer has confirmed the following certifications and documents. Coverage can differ by model, so we confirm which documents apply to the exact model and configuration you buy and provide copies.

MSDS

Material safety data sheet

Safety documentation covering handling, storage and emergency response.

UN38.3

Transport testing

UN transport testing for lithium batteries, used to qualify batteries for shipment.

IP67

Ingress protection

Rated dust-tight and protected against temporary immersion in water.

UL164224V 100Ah

Lithium cell safety standard

Available for the 24V 100Ah model. UL1642 covers lithium cells; it is not a UL listing of the complete battery.

Specification sheet

Electrical and mechanical specifications for your model and configuration.

Project-specific test reports

The manufacturer holds test data and reports, including temperature and cycle-life testing. Send your requirements; the manufacturer verifies each item and provides accurate data for your application.

Other certifications your market requires can be reviewed with the manufacturer for your project.

OEMs and integrators

Submit your application requirements

For engineered applications, the manufacturer reviews each requirement before we confirm a battery or configuration. The more you can share, the faster we can respond accurately.

  • Intended application and operating environment
  • Required voltage and capacity
  • Minimum and maximum operating temperatures
  • Charging and discharge current requirements
  • Quantity and forecast annual volume
  • Mechanical, size and packaging requirements
  • Monitoring and communication requirements
  • Required certifications and test documentation

Need pricing for a known model?

Send us your volume and application details.

Request Wholesale Pricing